|
|
|
|
|
|
|
|
|
|
|
|
|
|
Airbox door seal for Classic Edge models. (silicone adhesive not included). Table provides actual length; however, seal must be purchased in lengths of feet. Cutting may be required. When ordering, specify the length in feet.
|
Replacement spring for furnace models using stepper motors on the air intake assemblies. Two each used per assembly. For Classic Edge 350, 550 and 750 models.
|
Foam with adhesive, 3/8” thick x 3/4” wide. When ordering specify the length in feet.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Kit for insulating the Reaction Chamber thermocouple on Classic Edge Titanium HD models. Includes insulating sleeve and O-ring.
|
Replacement spring on these furnace models using solenoids on the primary air intake assemblies. - Classic Edge 350, 550 models with steel elbows.
|
Replacement sight gauge tube only (12" x 9/16" OD x 3/8" ID). Please note, if you need all parts listed in the picture, they must be purchased separately. Use the parts listed for each part you require.
Classic Edge models use 6" length. CleanFire models use 6" length. E-Classic 1450, 3200 & 3250 models use 6" length. E-Classic 1400, 2300 & 2400 models use 7" length. Forge 1500 & 3500 models use 9" length. Classic 4030, 5036, 6048 & 7260 models use 9" length. Pallet Burner models use 14" length.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement wingnut for Reaction Chamber door on Classic Edge and E-Classic models.
|
Replacement Bypass alarm switch for E-Classic IR models, Classic Edge 550/560/750/760/960 models; Replacement Gas Burner Switch for E-Classic IR/DF and Classic Dual Ready models.
|
Replacement spring on these furnace models using solenoids on the primary air intake assemblies. - Classic Edge 350, 550 & 750 models with molded elbows. - Classic Edge 750 models with steel elbows. - E-Classic 3250 models with molded elbow. - E-Classic 1400, 1450, 2300, 2400 & 3200 models with steel elbows.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement insulation strap (30") for rear cleanout door on Classic Edge 350 HD/360 HDX. Uses 2 per door.
|
Replacement insulation strap (33.75") for rear cleanout door on Classic Edge 550 HD/560 HDX models. Uses 2 per door.
|
Replacement insulation strap (42.50") for rear cleanout door on Classic Edge 750 HD and Classic Edge 760/865/960 HDX models. Uses 2 per door.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement Firebox Door Switch for E-Classic DF and Ignition Ready, Forge and Classic Edge furnaces. Replacement Reaction Chamber door switch and firebox door switch for Classic Edge HDX, rear cleanout door for Classic Edge 865 HDX.
|
Replacement retainer pin for Fireball tunnel refractory on Classic Edge 865 models. Qty 4 required.
|
Replacement Pump Panel Latch for Classic Edge models.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement bushing (1) with collar (1) for cam latch/cam lock for firebox door. For Classic Edge models and Forge models.
|
Replacement insulation for rear cleanout door attached with metal straps on Classic Edge 350 HD/360 HDX models.
|
Replacement insulation for rear cleanout door attached with metal straps on Classic Edge 550 HD models.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement retainer pin for Fireball tunnel refractory on Classic Edge 960 models. Qty 4 required.
|
Replacement closeoff plate asm for primary intake on all E-Classic and Classic Edge models with steel elbows. Replacement closeoff plate asm for high secondary intake on all E-Classic models except the 1450.
|
Replacement snap disc for Classic Edge and and for M255 models with s/n M210447 and earlier. Snap Disc, 180°-205°F (High Limit Water Jacket)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement rubber elbow for secondary air inlet on Classic Edge and Forge models. Use part number 2500526 for primary air intake on Classic Edge, E-Classic 3250 and Forge models.
|
Replacement insulation for inside of rear cleanout door on Classic Edge 350 HD/360 HDX models. Dimensions: 10.875" X 31.625"
|
Replacement insulation for inside of rear cleanout door on Classic Edge 550 HD/560 HDX models. Dimensions: 10.875" X 35.375"
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Tool for cleaning Afterburner and Reaction Chamber on Classic Edge HDX 360/560/760 models.
|
Replacement insulation for INNER part of rear cleanout door on Classic Edge 750 HD/760 HDX/865 HDX/960 HDX models. Dimensions: 13.25" X 44.25"
|
Heat exchanger/door frame cleaning tool for Classic Edge 350/360, 550/560, 750/760, 960 models.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Air channel clamps for round combustion air tubes for Classic Edge 350/550, LH (Left-hand side only). For right side, please add part 2001276 to your cart.
|
Air channel clamps for round combustion air tubes for Classic Edge 350/550, RH (right-hand side only). For left side, please add part 2001275 to your cart.
|
Air channel clamps for round combustion air tubes for Classic Edge 750, LH (left-hand side only). For right side, please add part 2001278 to your cart.
|
|
|
