|
|
|
|
|
|
|
|
|
|
|
|
|
|
Manifold Loop Cap can be used with Stainless Steel Radiant Manifold Kits.
|
Foam with adhesive, 3/8” thick x 3/4” wide. When ordering specify the length in feet.
|
Manifold Temperature Gauge can be used with Stainless Steel Radiant Manifold Kits.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement sight gauge tube only (12" x 9/16" OD x 3/8" ID). Please note, if you need all parts listed in the picture, they must be purchased separately. Use the parts listed for each part you require.
Classic Edge models use 6" length. CleanFire models use 6" length. E-Classic 1450, 3200 & 3250 models use 6" length. E-Classic 1400, 2300 & 2400 models use 7" length. Forge 1500 & 3500 models use 9" length. Classic 4030, 5036, 6048 & 7260 models use 9" length. Pallet Burner models use 14" length.
|
Rubber Clamp accessory for holding cleaning tools. Includes one clamp. Mounts with bolts or screws (not included). Size: .63" - 1.38"
|
Replacement O-Ring for Hot Water Filter Cartridge. Hot water filter cartridges (Part 202) sold separately
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
O-Ring, replacement for hot water sediment trapper filter (part number 2900578).
|
Rubber Clamp accessory for holding cleaning tools. Includes one clamp. Mounts with bolts or screws (not included). Size: 1.00" - 2.25"
|
O-Ring, replacement for hot water sediment trapper filter (part number 2900587).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Gauge is 1/8" MPT, 1" diameter with 1" stem length, for use in tight areas. Temperature Gauge, 1/8" MPT
|
Replacement antenna only for FireStar XP Outdoor Wi-Fi Module, RP-SMA Male, 6.6”
|
Replacement Firebox Door Switch for E-Classic DF and Ignition Ready, Forge and Classic Edge furnaces. Replacement Reaction Chamber door switch and firebox door switch for Classic Edge HDX, rear cleanout door for Classic Edge 865 HDX.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement 48" twisted wire chimney brush extension rod only. Twisted wire extension rod is a component of Chimney Cleaning Kit (part number 2500296) for cleaning both the horizontal and vertical portions of all 6" chimneys.
Note regarding shipping: This is an oversized product cannot be shipped via USPS Priority Mail. Please choose UPS Ground shipping method upon checkout.
|
Replacement chimney brush handle only. Handle is a component of Chimney Cleaning Kit (part number 2500296) for cleaning both the horizontal and vertical portions of all 6" chimneys.
Note regarding shipping: This is an oversized product 2900490 cannot be shipped via USPS Priority Mail. Please choose UPS Ground shipping method upon checkout.
|
Replacement 72" twisted wire chimney brush extension rod only. Twisted wire extension rod is a component of Chimney Cleaning Kit (part number 2500296) for cleaning both the horizontal and vertical portions of all 6" chimneys.
Note regarding shipping: This is an oversized product cannot be shipped via USPS Priority Mail. Please choose UPS Ground shipping method upon checkout.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used to connect a 24-volt thermostat to existing thermostat for a heat pump.
|
Tool with six interchangeable heads for straightening fins on water-to-air heat exchangers. For all units with 8,9,10,11,12 and 14 fins per inch.
|
Replacement 6" Chimney brush only. Brush is a component of Chimney Cleaning Kit (part number 2500296) for cleaning both the horizontal and vertical portions of all 6" chimneys.
Note regarding shipping: This is an oversized product cannot be shipped via USPS Priority Mail. Please choose UPS Ground shipping method upon checkout.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement rubber elbow for secondary air inlet on Classic Edge and Forge models. Use part number 2500526 for primary air intake on Classic Edge, E-Classic 3250 and Forge models.
|
Measures accurately the moisture level of wood with a range of 6% - 42%, and the ambient temperature (°C/°F). Mini in size and portable for field works, very easy to operate and delivers accurate readings instantly.
|
In-line, dial temperature gauge with 1/2" MPT (p/n 174) and 4" stem is optional for manifold, pool heater, systems, etc. Temperature Gauge, 1/2" MPT
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Kit includes door seal rope cut to length (10 ft) and instructions. Silicone is not included. For Classic 4030, 5036, 6048 model firebox doors, Hydrofire models and Forge 1500, 3500 model firebox doors. For cast door and steel door models if applicable. Forge 1500/3500- uses 6.5 ft Classic 4030/5036- uses 8 ft Classic 6048- uses 9 ft
|
Hot water filter cartridge, #10 (replaces Part 101) for Hot Water Filter. Replacement O-Ring for Hot Water Filter Cartridge (Part 5000397) sold separately
|
Socket, 5-A
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Buss Screw-in Type Fuse, 5-A, (PKG QTY - 5).
NOTE: Price shown is for 5 units; will ship with PKG QTY and approximate shipping weight indicated.
|
Used with components such as snap discs and temperature probes where heat transfer is necessary.
|
Used to mount a Wi-Fi antenna (not included) to the lift tab of the furnace.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement rubber elbow with ring insert for;
- primary air inlet on Classic Edge models with stepper motors (use p/n 5500016 for secondary)
- primary air inlet on E-Classic 3250 and Classic Edge models with molded elbow/solenoid
- primary air inlet on Forge models with stepper motors (use p/n 5500016 for secondary)
Kit includes primary air inlet elbow with ring insert and rubber.
|
Y-Strainer with .20 mesh and FIP fittings. Recommended when installing plate-style heat exchangers. Use 1/2" Brass Pipe Plug (p/n 6557) for cleanout port.
|
Replacement screen for Hot Water Filter (p/n 2900578).
|
|
|
