|
|
|
|
|
|
|
|
|
|
|
Replacement Fuse: The 3-A fuse is used for power disconnect on Classic Standard models. Also used if a side draft inducer is installed.
|
Price per foot for 7/8" braided door seal rope. When ordering specify the length in feet. NOTE: Silicone is not included.
|
Reaction Chamber Firebrick, 9" x 4.5" x 1.25".
NOTE: Replacement firebrick for E-Classic Reaction Chamber is available in different sizes. Refer to Technical Specifications for model specific quantities of firebrick installed in the Reaction Chamber.
|
|
|
|
|
|
|
|
|
|
|
|
|
Reaction Chamber Firebrick, 6.625" x 4.5" x 1.25".
NOTE: Replacement firebrick for E-Classic Reaction Chamber is available in different sizes. Refer to Technical Specifications for model specific quantities of firebrick installed in the Reaction Chamber.
|
Replacement close-off plate for low secondary intake on all E-Classic models except the 1450.
|
Reaction Chamber Firebrick, 4.5" x 4.5" x 1.25".
NOTE: Replacement firebrick for E-Classic Reaction Chamber is available in different sizes. Refer to Technical Specifications for model specific quantities of firebrick installed in the Reaction Chamber.
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement ignitor burner gasket for E-Classic 2300 models.
|
Reaction Chamber Firebrick, 4" x 4.5".
NOTE: Replacement firebrick for E-Classic Reaction Chamber is available in different sizes. Refer to Technical Specifications for model specific quantities of firebrick installed in the Reaction Chamber.
|
Clear tubing for the E-Classic air proving switch. 10 feet required for E-Classic models.
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement sight gauge tube only (12" x 9/16" OD x 3/8" ID). Please note, if you need all parts listed in the picture, they must be purchased separately. Use the parts listed for each part you require.
Classic Edge models use 6" length. CleanFire models use 6" length. E-Classic 1450, 3200 & 3250 models use 6" length. E-Classic 1400, 2300 & 2400 models use 7" length. Forge 1500 & 3500 models use 9" length. Classic 4030, 5036, 6048 & 7260 models use 9" length. Pallet Burner models use 14" length.
|
Replacement Bypass alarm switch for E-Classic IR models, Classic Edge 550/560/750/760/960 models; Replacement Gas Burner Switch for E-Classic IR/DF and Classic Dual Ready models.
|
Replacement spring on these furnace models using solenoids on the primary air intake assemblies. - Classic Edge 350, 550 & 750 models with molded elbows. - Classic Edge 750 models with steel elbows. - E-Classic 3250 models with molded elbow. - E-Classic 1400, 1450, 2300, 2400 & 3200 models with steel elbows.
|
|
|
|
|
|
|
|
|
|
|
|
|
E-Classic replacement latch spring clips for rear panels and Reaction Chamber panel. Set of 5 clips.
|
Short replacement turbulator for E-Classic 2300 models. Note there are three different lengths.
|
Replacement Firebox Door Switch for E-Classic DF and Ignition Ready, Forge and Classic Edge furnaces. Replacement Reaction Chamber Door Switch for Classic Edge HDX models.
|
|
|
|
|
|
|
|
|
|
|
|
|
Medium replacement turbulator for E-Classic 2300 models. Note there are three different lengths.
|
Long replacement turbulator for E-Classic 2300 models. Note there are three different lengths.
|
Curved Refractory only for E-Classic 2300 models. Dimensions: approximately 1.6" x 4" x 11". Also see p/n 2500055 and 2500056 for Fushion Combustor Kit.
|
|
|
|
|
|
|
|
|
|
|
|
|
Drip Edge, Classic Edge 350. NOTE: When installing a replacement Front Air Channel Kit for early production Classic Edge model furnaces that have the top of the front air channel bolted to the bottom of the door frame, it is recommended to weld a drip edge.
|
Temperature Sensor Well used with digital temperature controllers (p/n 2000155 and 8320).
|
Drip Edge, Classic Edge 550. NOTE: When installing a replacement Front Air Channel Kit for early production Classic Edge model furnaces that have the top of the front air channel bolted to the bottom of the door frame, it is recommended to weld a drip edge.
|
|
|
|
|
|
|
|
|
|
|
|
|
Attached to Cleaning Rod (p/n 9439) for cleaning the refractory slot.
|
Replacement Flue Brush only, used to clean the flue passageways of E-Classic 2300 and M175 models. Not to be used for cleaning 6" or 8" chimney. Flue Brush for use with handle (part number 2900490) and extension rod (part number 312). Available as a kit (part number 310).
Note regarding shipping: This is an oversized product cannot be shipped via USPS Priority Mail. Please choose UPS Ground shipping method upon checkout.
|
Drip Edge, Classic Edge 750. NOTE: When installing a replacement Front Air Channel Kit for early production Classic Edge model furnaces that have the top of the front air channel bolted to the bottom of the door frame, it is recommended to weld a drip edge.
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement Rocker Switch, Power Supply (on-off), 5A breaker
|
Replacement 8" Chimney brush only. Brush is a component of Chimney Cleaning Kit (part number 2500297) for cleaning both the horizontal and vertical portions of all 8" chimneys. Note regarding shipping: This is an oversized product cannot be shipped via USPS Priority Mail. Please choose UPS Ground shipping method upon checkout.
|
Extension rod only, used to clean both the horizontal and vertical portions of all 6" and 8" chimneys. For use with handle (part number 2900490) and flue brush (part number 311). Available as a kit (part numbers 310 and 390).
Note regarding shipping: This is an oversized product cannot be shipped via USPS Priority Mail. Please choose UPS Ground shipping method upon checkout.
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement closeoff plate asm for primary intake on all E-Classic and Classic Edge models with steel elbows. Replacement closeoff plate asm for high secondary intake on all E-Classic models except the 1450.
|
Protects transformer from short circuit. For E-Classic models.
|
Replacement rubber elbow for secondary air inlet on Classic Edge and Forge models. Use part number 2500526 for primary air intake on Classic Edge, E-Classic 3250 and Forge models.
|
|